71M6511/71M6511H
Single-Phase Energy Meter IC
A Maxim Integrated Products Brand
DATA SHEET
NOVEMBER 2010
XFER_BUSY interrupt. After these first two cycles, CHOP_EN returns to 11 (automatic toggle). The value of CHOP_EN , when
set after the XFER_BUSY interrupt, is in force for the entire following multiplexer cycle.
When using this sequence, the alternate multiplexer cycle is toggled between positive and reversed connection resulting in
accurate temperature measurement.
An example for proper application of the CHOP_EN bits can be found in the Demo Code shipped with the 6511 and 6511
Demo Kits. Firmware implementations should closely follow this example.
Accumulation Interval m
Accumulation Interval m+1
Accumulation Interval m+2
alt. MUX
cycle
MUX
cycle 2
MUX
cycle 3
MUX
cycle n
alt. MUX
cycle
MUX
cycle 2
MUX
cycle 3
MUX
cycle n
alt. MUX
cycle
MUX
cycle 2
MUX
cycle 3
MUX
cycle n
Chop Polarity
re-
Positive Positive versed
Positive
re-
versed
re-
versed
Positive
re-
versed
Positive Positive
re-
versed
Positive
CE_BUSY interrupt
XFER_BUSY interrupt
MUX_ALT
CHOP_EN
01
11
(11)
(11)
(11)
10
11
(11)
(11)
(11)
01
11
(11)
(11)
(11)
Figure 23: Sequence with Alternate Multiplexer Cycles and Controlled Chopping
Internal/External Pulse Generation and Pulse Counting
The CE is the source for pulses. It can generate pulses directly based on the voltage and current inputs and the configured
pulse generation parameters. This is called “internal pulse generation”, and applies when the CE RAM register EXT_PULSE
(address 0x37) equals 0. Alternatively, the CE can be configured to generate pulses based on registers that are controlled by
the MPU (“external pulse generation”), i.e. when the register EXT_PULSE equals 15. In the case of external pulse generation,
the MPU writes values to the CE registers APULSEW (0x26) and APULSER (0x27).
The pulse rate, usually inversely expressed as “Kh” (and measured in Wh per pulse), is determined by the CE RAM registers
WRATE , PULSE_SLOW , PULSE_FAST , In_8 , as well as by the sensor scaling VMAX and IMAX per the equation:
Kh =
VMAX ? IMAX ? 47.1132
In _ 8 ? WRATE ? N ACC ? X
[ Wh / pulse ]
where
In_8 is the gain factor (1 or 8) controlled by the CE variable In_SHUNT ,
X is the pulse gain factor controlled by the CE variables PULSE_SLOW and PULSE_FAST
N ACC is the accumulation count ( PRE_SAMPS * SUM_CYCLES )
Page: 55 of 98
? 2005–2010 Teridian Semiconductor Corporation
V2.7
相关PDF资料
71M6513H-IGT/F IC ENERGY METER 3PH 100-LQFP
71M6515H-IGT/F IC ENERGY METER AFE 3PH 64-LQFP
71M6521BE-IGTR/F IC ENERGY METER 8K FLASH 64-LQFP
71M6533G-IGTR/F IC ENERGY METER 3PH 100LQFP
71M6543F-IGT/F IC ENERGY METERING
71M6545-IGT/F IC ENERGY METERING
720-10007-00300 CBL D-SUB 9PIN FMAL-25PIN FML 3M
720-10010-00025 CBL DSUB 9PIN FML-25PIN MAL .25M
相关代理商/技术参数
71M6511-IGT 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Single-Phase Energy Meter IC
71M6511-IGT/F 功能描述:计量片上系统 - SoC Highly Integrated SoC w/MCU Core RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6511-IGT/F1 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6511-IGTR 制造商:TERIDIAN 制造商全称:TERIDIAN 功能描述:Single-Phase Energy Meter IC
71M6511-IGTR/F 功能描述:计量片上系统 - SoC Highly Integrated SoC w/MCU Core RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6511-IGTR/F1 功能描述:计量片上系统 - SoC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6512-DB 制造商:Maxim Integrated Products 功能描述:Development Boards & Kits - 8051 71M6512 Demo Brd
71M6512-IM/F 制造商:Maxim Integrated Products 功能描述:Metering Systems on a Chip - SoC Residential Meter Extended Io